Partial wallpaper quantity calculator

Wallpaper width

Wallpaper length

Surcharge (Loss]

Construction area #1

width

length

Please check.

You must prepare based on the 'number of strips' obtained by dividing the width of the wall by the width of the wallpaper to prevent construction from being halted due to the inability to fill the last strip.
Since the wall heights at the site are often not level, you must add a cutting allowance of 100mm (10cm] to the actual height to avoid running out of material.
Please note that you must add the pattern repeat value to the height when cutting to ensure the pattern on the side width matches the design seamlessly and without errors.
If you apply it directly over existing silk wallpaper, the adhesive strength is weak and it may peel off quickly, so you must completely remove the vinyl layer from the surface before installation.
Since slight color differences may occur due to different production lots, the standard practice in the field is to place the entire calculated order at once instead of placing additional orders.

How about this calculator?

Partial Wallpaper Calculator, Perfect Guide to Calculating Accent Wallpaper and Partial Wallpaper Quantity

When partially wallpapering a living room accent wall or just one wall, the biggest concern is the amount of wallpaper required. Accent wallpapers, in particular, often result in significant waste due to pattern matching, making it easy to end up short by a single roll. This calculator accurately determines the required number of rolls by reflecting actual measurements and material loss rates. Use it as a reliable reference value for a successful DIY interior project before placing your materials order.

Formula for Calculating Partial Wallpaper Requirements

For partial wallpapering, the key to minimizing errors is to first determine the required 'width' by dividing the horizontal length of the wall by the width of the wallpaper.

1. Calculate the required width

Required width = Wall width ÷ Wallpaper width (Result is always rounded up]

Calculate the number of wallpapers to be laid vertically to cover the entire wall surface.

2. Calculation of required length per width (considering patterns]

Required length per width = Wall height + Cutting allowance (100mm] + Pattern repeat value

You must calculate not only the simple height but also the top and bottom trimming allowances and the sections discarded to match the pattern.

3. Calculation of Final Required Roll Count

Final number of rolls = (Number of required widths × Length per width] ÷ Length of one roll of wallpaper (Round up result]

Determine the final order quantity by dividing the total required length by the length of one roll of wallpaper to be purchased.

Detailed Guide to Calculator Input Items

Please enter the detailed specifications and actual measurements of the wallpaper to be purchased to calculate the exact quantity required.

1. Wallpaper width/length
This is the width and total length of the roll of wallpaper you intend to purchase.
2. Construction Area Width
It is the straight-line distance from the left end to the right end of the wall to be partially wallpapered.
3. Construction area length
It is the pure vertical height from the top of the baseboard to the bottom of the ceiling molding.
4. Surcharge rate
This is an allowance to cover cutting errors and pattern misalignment. If the pattern is large, we recommend setting it to 10% or more.

Standard Specifications and Features by Wallpaper Type

Since the width varies depending on the type of wallpaper selected, please be sure to check the specifications before taking actual measurements.

Types of wallpaper	Standard Width	Standard Length	Remarks (Field Terms]
Silk wallpaper (wide]	1,060 mm	15.6 m	Approx. 5 pyeong installation, no seams
Laminated wallpaper (wide]	930 mm	17.5 m	Construction of approximately 5 pyeong, economical
Laminated wallpaper (narrow width]	530 mm	12.5 m	Installation of approximately 2 square meters, recommended for beginners
Imported / Accent Wallpaper	500 ~ 700 mm	10.0 m	Pattern repetition (Repeat] verification is essential

note.

Since a lot of colorful accent wallpaper is wasted during the pattern matching process, it is recommended to prepare about one roll extra.

Essential Checklist for Fail-Free Construction

Here is key practical know-how to minimize failures when doing partial wallpapering yourself.

Check pattern alignment
If the pattern repeat cycle is 60cm, up to 60cm may be wasted per width. If the pattern is large, be sure to add an extra roll.
Using a laser level
If the first strip is not attached vertically, the wallpaper will tilt noticeably towards the last strip. Securing a baseline is essential.
Removal of the outer surface of silk wallpaper
If you apply it over silk wallpaper, it will fall off quickly. Be sure to remove the vinyl layer from the existing silk wallpaper before installation.
Principle of natural drying
The wrinkling immediately after installation will smooth out as it dries. It is important to avoid cross drafts and dry it slowly for 2 to 3 days with the windows closed.

Frequently Asked Questions (FAQ]

Q. The wall height is 2.3m; does one 7m roll yield 3 widths?
A. It is not possible. Including the top and bottom trimming allowances (5cm each], a minimum of 2.4m is required per width, so only 2 widths can be installed with one roll.

Q. Why is calculating the width more important than calculating the area (㎡]?
A. This is because even if the materials appear sufficient in terms of area, construction cannot be completed if the width of the final wall is not filled. For wallpapering, materials must always be prepared in 'width' units.

Q. How much paste do I need for DIY wallpapering?
A. Typically, 2 to 3 bags (1kg/bag] of wallpaper paste are required per roll of wallpaper (for a 5-pyeong area]. For accent wallpaper, it is recommended to mix in <strong>Z-Flex (glue]</strong> for better adhesion.

Q. The wall height is 2300mm, so why do I need to add 100mm to the calculation?
A. This is because walls on actual construction sites are often not perfectly level or vertical. To achieve a seamless and clean finish, you must apply the wallpaper leaving a margin of approximately 50mm at both the top (ceiling] and bottom (baseboard] ends, and then precisely trim the excess with a knife.